This post listed below relating to Installing A Bathtub is seriously compelling. Have a go and make your own final thoughts.
Installing a tub isn't exactly brain surgery, but it does need strong plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably difficult project. If the old bathtub is conveniently easily accessible, the project can move rapidly; if you need to open a wall surface to remove the old bathtub and also position the brand-new bath tub, the job is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require a helper to vacate the old tub and embeded in the brand-new one. Make certain you have actually certified on your own for the task as well as fit trying it. Instead of employing a specialist to take over a halfway-completed job, it is far better to take into consideration employing one prior to you start. Possibilities are you may need a specialist plumber to make tube links.
This post will certainly help you mount a brand-new bath tub in your shower room if you have already gotten a brand-new tub as well as do not need to change the plan of your previous water system pipelines.
Your tools and also material list should comprise the following:
Planning for the Installment
To start with, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to make sure that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to avoid pressure on the tub.
Fit the adaptable tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must currently prepare to be suited its last placement.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, switch on the taps to drain any water remaining in the system. The process of removing the existing faucets can be quite bothersome due to the limited access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a fabric ready for the staying water that will certainly originate from the pipelines. When the supply pipes have been removed, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Prior to proceeding to fit the new faucets, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Utilizing both wood boards under its feet, position the bath tub in the called for placement. The wood boards are valuable in equally spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four little factors.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the spirit level as well as adjusting the feet on the tub till the level checks out level.
To set up faucets, fit all-time low of the outermost versatile tap connector to the ideal supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the water system as well as examine all joints and brand-new pipework for leakages and tighten them if essential. Load the bathtub and also check the overflow outlet and the typical outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub must wait till the tub has been utilized at least when as this will resolve it right into its last position.
Fitting New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the placing opening in the bath/basin making certain that the washers are in place between the faucet and the sink. Protect the tap in position with the maker given backnut. When the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The former type should be attached to the faucet ends first, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to split a stiff seal, triggering the water to permeate the wall surface in between the bath and also the tiling, leading to problems with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes as well as cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the tub with water before sealing, to enable the movement experienced when the bathtub remains in use. The sealant can fracture fairly very early if you do not take into consideration this movement prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Hopefully you liked our article about Tools You Need to Install a New Bathtub . Many thanks for spending some time to read through our posting. I beg you take the time to share this article if you enjoyed reading it. Bless you for your time. Please check our blog back soon.
About This